Safety in the Laundry Area

A clothes dryer doesn't look scary or appear to be too dangerous. Unfortunately, it is the cause of over fires every year totaling millions of peso in damage. Regular cleaning and maintenance can protect you and your investment.

Get Rid of Dreaded Lint
Whether you use an electric or gas clothes dryer, you will have lint. Lint builds up in the lint trap but also inside the dryer hose and vent and can reduce air flow and drying efficiency. Lint can cause humidity levels to rise around vents causing mildew and mold to develop in walls and insulation. But most important to remember: Lint is combustible. Lint causes fires.
Fortunately, removing dangerous lint is simple. The first area to clean is the lint trap. It should be cleaned after every load by removing the lint from the screen and wiping the edges. If the screen seems clogged, it may be front the dryer sheets you have been using. Submerge the lint screen in a sink of hot water and then scrub with a bristle brush to remove all the built-up fabric softener.
The key to success in de-linting a dryer is a dryer lint brush. This long-handled flexible brush will help you reach areas that you cannot get to by hand.
Remove the dryer lint filter. In the opening - whether on dryer top or in door, use the brush to gently loosen the built-up lint. Don't force the brush if you meet resistance but be sure to cover every surface as much as possible. Remove the big chunks of lint that come out with the brush. Don't worry about the smaller pieces.
Replace the lint filter (which I'm sure you have cleaned). Turn the dryer to air only and run for a cycle. This will pull the lint into the filter or blow the loose particles out the outside vent.
At least once per year, unplug the dryer and check where the exhaust hose connects to the dryer. The hose or pipe is held in place by a clip or a steel clamp that can be loosened by pliers or a screwdriver. After removing the pipe, reach inside the dryer opening or use a vent brush to remove as much lint as possible. A shop vacuum is handy for removing the most lint and use a damp cloth to wipe away remaining lint around the connection.
Look inside the hose or pipe and clean it as well. If your exhaust hose is vinyl or foil it should be replaced with a flexible metal pipe with flexible fittings. Most building codes no longer allow vinyl or foil exhausts.
One last step is to clean the exterior vent. Again remove as much lint as possible using your hand or a shop vacuum. You may need a screwdriver or another tool to hold the vent flap open for easier cleaning. If you live in a high humidity area or use your dryer more than twice weekly, you may need to clean this vent several times per year.

Using the Dryer Safely
If possible, clothing that has been soiled by volatile chemicals like gasoline, cleaning agents or even large amounts of cooking oil should not be dried in a clothes dryer. If they must be dried in the machine, wash the clothing more than once to minimize the risk of fire. Use the lowest heat setting and shortest drying cycle possible. Use a cycle with a cool-down period at the end of the cycle to prevent ignition.

Installing the Dryer Correctly
A clothes dryer should not vent inside. The exhaust contains too much humid air and can cause problems with mold and mildew which are hazardous to health. A vent less dryer should be used if outside venting is not possible.
Be certain that you have a 220v grounded electrical outlet available for an electric dryer. A professional should used to install gas lines for gas dryers.

Never store volatile chemicals or rags near a dryer. Some liquids emit vapors than ignite. The area around the dryer should be kept free of lint, papers and stacks of clothing.

LPG maintenance

• Always keep the LPG valve / regulator switched off when not in use, especially at night after the work is done and when going on a holiday.
•  LPG should also be sealed and place inside a cage.
• Always store the LPG cylinder in an upright position and away from other combustible and flammable materials. Store no more than one spare LPG cylinder at any given time.
• Check for gas leaks regularly by applying soap solution on cylinder joints. The appearance of soap bubbles indicates leak points. Do not use open flame to detect leaks.
• Always replace worn-out or defective tubing and regulators. Half of all gas-related accidents occur due to leakages from the rubber tube. Change the tubing every two years and the regulator every five years.
• Make sure all parts of the installation are in good condition. If you should find anything wrong with any part, contact your distributor immediately and ask for assistance.
• Never tamper with your LPG cylinder.